FL3557 – Quick Tie Products, Inc.
Florida product approval FL3557-R32 for Structural Components – Wood connector/anchor, as listed in ProdApproval’s data as of Sep 29, 2026.
- FL#
- FL3557-R32
- Manufacturer
- Quick Tie Products, Inc.
- Code version
- 2023 Florida Building Code
- Status in our data
- Approved
- Products
- 30
Official record on floridabuilding.org →Use on a spec sheet →
Verify approval status on floridabuilding.org before submitting.
Approved products under FL3557-R32
| Approval # | Model | Description | Design pressure | Wind-borne debris | HVHZ | Outside HVHZ |
|---|---|---|---|---|---|---|
| FL3557.1 | CMST16-54, CMST14-52.5, and CMST12-40 Coiled Straps | Coiled Straps (CMST) are either 16 gauge, 14 gauge, or 12 gauge. Each strap is 3" wide with 0.177" diameter nail holes punched at 1-½" intervals along its length. | N/A | N/A | Yes | Yes |
| FL3557.2 | CS20-250, CS18-200, CS16-150 & CS14-100 Coiled Straps | - Coiled Straps are 20 gauge steel (CS20-250), 18 gauge steel (CS18-200), 16 gauge steel (CS16-150), or 14 gauge steel (CS14-100). | N/A | N/A | Yes | Yes |
| FL3557.3 | FASA4 Foundation Anchor Strap | FASA4 Foundation Anchor Strap is a cast-in-place connector designed for use as an alternative to anchor bolts. | N/A | N/A | Yes | Yes |
| FL3557.4 | FSTHD and FSTHDJ Foundation Strap-Tie Hold Downs | FSTHD8, FSTHD8J, FSTHD10, FSTHD10J, FSTHD14 and FSTHD14J are embedded strap-tie hold downs designed to secure a structure, wood-framed walls, to its foundation. | N/A | N/A | Yes | Yes |
| FL3557.5 | HA4, HA 6 and HA8 Hurricane/Seismic Clip | 18 gauge (minimum thickness with coating 0.0466") steel clips are used to fasten rafters and trusses to wall top plates. | N/A | N/A | Yes | Yes |
| FL3557.6 | HD8 Hold Down | Hold Down Connectors used to anchor stud walls and/or posts into concrete. | N/A | N/A | Yes | Yes |
| FL3557.7 | HDTT, HD5, HD7, HD11, HD14, and HD15/20 Hold Downs | HDTT, HD5, HD7, HD11, HD14, and HD15/20 Hold Downs | N/A | N/A | Yes | Yes |
| FL3557.8 | HDTT3 Hold Down, HD22 Hold Down and HDTT6 Hold Down | HDTT3 and HD22 are used to anchor stud walls and/or posts into concrete; HDTT6 Hold Down Connectors are used to anchor stud walls into concrete. | N/A | N/A | Yes | Yes |
| FL3557.9 | HDTT45 Hold Down | HDTT45 Hold Down Connectors are used to anchor stud walls into concrete. | N/A | N/A | Yes | Yes |
| FL3557.10 | HGA and HGAM Gusset Angles | The HGA and HGAM are a 90° framing angle used to connect truss/rafter joists to wall top plates and masonry. | N/A | N/A | Yes | Yes |
| FL3557.11 | LS and MS series straps | Galvanized steel straps, 1-1/4 inches wide and in varying length from 9-5/8 inches to 48-5/8 inches in length with minimum thicknesses of 0.0356 inches (LS) and 0.0575 inch (MS). | N/A | N/A | Yes | Yes |
| FL3557.12 | LTS, MTS, and HTS Twist Straps | Light Twist Straps (LTS), Medium Twist Straps (MTS), and Heavy Twist Straps (HTS) come in different lengths. Straps have an offset shape to allow twisting and bending. | N/A | N/A | Yes | Yes |
| FL3557.13 | LTT20 Light Tension Tie, QGC QuickTie Girder Connector, HA10 Hurricane Seismic Anchors | LTT ties connect wall bottom plates/studs or joist/purlin-to-wall attachment apps. QGC connect truss & rafter to top plate where uplift load design requirements are high. HA10 are 18 gauge steel clips that fasten rafters and trusses to wall top plates. | N/A | N/A | Yes | Yes |
| FL3557.14 | METAS/HETAS and PCS/PCES | METAS-HETAS are embedded anchors designed to connect truss/rafter joists to the top of concrete masonry unit and concrete walls. PCS are used to join center posts to beams. PCES are used to join end posts to beams | N/A | N/A | Yes | Yes |
| FL3557.15 | PAS18-3Z, PAS23-3Z, PAS28-3Z, PAS35-3Z and PAS51-3Z Purlin Anchor Straps | Embedded anchors designed to connect roof purlins to a concrete or CMU wall as a purlin anchor or to connect studs to the foundation as a strap-tie hold down. | N/A | N/A | Yes | Yes |
| FL3557.16 | PBA Post Base Anchors: PBA44, PBA46, PBA66, PBA77, PBA88, PBA44-4P/6P and PBA66-4P/6P | Post Base Anchors (PBAs) are used to attach the base of a wood post to a concrete foundation. The PBAs are comprised of a Post Base Strap and Stand-Off (SO) plate. | N/A | N/A | Yes | Yes |
| FL3557.17 | PCM & EPCM Post Caps | PCM & EPCM Post Caps are used for post-to-beam connection applications. PCM and EPCMs are designed to resist uplift and shear loads due to wind and seismic forces. | N/A | N/A | Yes | Yes |
| FL3557.18 | PHGT2, PHHGT3 and PHHGT4 Connectors | PHGT2, PHHGT3 and PHHGT4 connectors are tie downs used to join 2-ply, 3-ply or 4-ply girder trusses to wall frames or posts. | N/A | N/A | Yes | Yes |
| FL3557.19 | QGC and QGCW QuickTie Girder Connector | QuickTie Girder Connectors are used for truss and rafter to top plate connections where uplift load design requirements are high, and for stud hold down connections. | N/A | N/A | Yes | Yes |
| FL3557.20 | QuickTie Adhesives | QE-1 Epoxy Adhesive and QE-2 Epoxy Adhesive | N/A | N/A | Yes | Yes |
| FL3557.21 | QuickTie Screws: SWH, SWF, SWT, SWL | QuickTie Screws are manufactured from carbon steel wire using a standard cold-formed process followed by a heat-treating process. | N/A | N/A | Yes | Yes |
| FL3557.22 | QuickTie System (QTS): QTB(L) Blue, QTG(L) Green, QTO(L) Orange, QTR(L) Red | The QTS consists of wood frame QuickTie, QTX(L), where "X" is the QuickTie type/cable diameter and "L" is the length in feet. | N/A | N/A | Yes | Yes |
| FL3557.23 | RSPT4, RSPT6, and RSPT6-2 Stud Plate Ties | Connectors designed to connect wood studs to either top or sill plates of wood framed walls | N/A | N/A | Yes | Yes |
| FL3557.24 | SC34 Framing Angle | The SC34 anchor floor and ceiling joists to headers. The SC34 uses a 90° framing angle to join posts to beams and to make other right-angle connections. | N/A | N/A | Yes | Yes |
| FL3557.25 | SC35 Framing Angle and SC35F Framing Plate | The SC35 anchors floor and ceiling joists to headers. The SC35F provides solid blocking to top plates. The SC35 uses a 90° framing angle to join posts to beams and to make other right-angle connections. | N/A | N/A | Yes | Yes |
| FL3557.26 | SPArtan Sill Plate Anchor | SPArtan™ Sill Plate Anchors are post-installed anchors used to attach the sill plate of a wood framed wall to a concrete foundation. | N/A | N/A | Yes | Yes |
| FL3557.27 | TCC16L, TCC16R, TCC21L and TCC21R Drag Strut Connectors | TCC16L, TCC16R, TCC21L and TCC21R connectors are Tension-Compression drag strut connectors used to transfer lateral forces from a truss to shear walls. | N/A | N/A | Yes | Yes |
| FL3557.28 | TCS 18-3Z and TCS20-3Z Tension-Compression Straps | Connectors designed to bridge/repair discontinuous wood members by transferring axial loads from one member to the other connected member | N/A | N/A | Yes | Yes |
| FL3557.29 | TR1 and TR2 Roof Truss Clips | TR1 and TR2 Roof Truss Clips are connectors designed for alignment control between a roof truss and non-loadbearing walls. | N/A | N/A | Yes | Yes |
| FL3557.30 | U-Hanger Series: UL, ULU, ULP & ULP-IF, UM, UH & UH-IF, TFLP, TFH; TSH; THJH; UMH; UHH; ULPSSH; UMSR-L; UHSR-L; UHD | U-Hanger and Inverted Flange (IF) U-Hanger Series are face mount joist hangers used to resist gravity loads and uplift loads due to wind in one-, two- and three-ply joist assemblies in light-frame wood construction. | N/A | N/A | Yes | Yes |
Fill a spec sheet with FL3557
On the contractor form, go to the Structural Components – Wood connector/anchor row and type 3557 in the Florida Product Approval # box to fill the row. Walton County users can print a PDF that follows the county’s sheet; see the Walton County Product Approval Specification Sheet guide.