Walton County Product Approval Specification Sheet
Fill out the Walton County Product Approval Specification Sheet online, then print a PDF that follows the county’s official sheet. Pick each product by manufacturer or FL approval number and the row fills in for you.
Fill out the Walton County sheet online →
When Walton County asks for it
The Walton County Building Department Checklist for Building Permits lists the sheet as item 9:
“9. Product Approval Specification Sheet – You may acquire approval numbers from the Vendor / Supplier or from www.floridabuilding.org. Note: This form must be signed.”
What the sheet asks for
The county’s Product Approval Specification Sheet starts with the project Location and Project Name. It cites Florida Statute 553.842 and Florida Administrative Code 9B-72. For each building component used on the project you list:
- Category / Subcategory
- Manufacturer
- Product Description
- Design Pressure (+/-)
- Wind Borne Debris Protection
- Approval Number(s)
Sections A–H
- A. Exterior Doors
- Swinging, Sliding, Sectional, Roll up, Automatic, Other
- B. Windows
- Single hung, Horizontal slider, Casement, Double hung, Fixed, Awning, Pass-through, Projected, Mullion, Wind breaker, Dual action, Other
- C. Panel Wall
- Siding, Soffits, EIFS, Storefronts, Curtain walls, Wall louver, Glass block, Membrane, Greenhouse, Other
- D. Roofing Products
- Asphalt shingles, Underlayments, Roofing fasteners, Non-structural metal roofing, Built-up roofing, Modified bitumen, Single ply roofing systems, Roofing tiles, Roofing insulation, Waterproofing, Wood shingles/shakes, Roofing slate, Liquid applied roof systems, Cements-adhesives-coatings, Roof tile adhesive, Spray applied polyurethane roof, Other
- E. Shutters
- Accordion, Bahama, Storm panels, Colonial, Roll-up, Equipment, Other
- F. Skylights
- Skylight, Other
- G. Structural Components
- Wood connector/anchor, Truss plates, Engineered, Railing, Coolers-freezers, Concrete admixtures, Material, Insulation forms, Plastics, Deck-roof, Wall, Sheds, Other
- H. New Exterior Envelope Products
- Two blank rows for products not listed above
The signature section
The sheet ends with a section for products that did not demonstrate product approval at plan review. The contractor states that, at inspection, the following must be available to the inspector on the jobsite: a copy of the product approval, the performance characteristics the product was tested and certified to comply with, and a copy of the manufacturer’s installation requirements, and that the products may have to be removed if approval cannot be demonstrated. It is signed by the contractor or the contractor’s authorized agent, with print name, date and location. The permit number is for staff use only.
How to fill it out on ProdApproval
- Open the contractor form and enter the Location and Project Name.
- In each row, choose a manufacturer and then a product, or type the digits of an FL approval number. The row fills in the product, design pressure, wind borne debris protection and approval number.
- Click Print PDF. Searching and filling are free; printing requires signing in. The Free plan includes 3 prints or exports per calendar month (Central Time), and Solo and Firm plans are unlimited.
- Sign the PDF. Walton County’s checklist notes that the form must be signed.
The PDF follows the county’s title, instructions, columns and sections A–H, and includes the signature page. It also adds a section I for impact protective systems. It is a rebuilt PDF, not the county’s own file.
New to spec sheets? Read How to fill out a Florida product approval specification sheet.
Start the Walton County sheet →
Walton County product approval sheet FAQ
What is the Walton County Product Approval Specification Sheet?
It is a Walton County Building Department form titled “Product Approval Specification Sheet.” For each building component used on the project it asks for the manufacturer, product description, design pressure (+/-), wind borne debris protection and approval number(s). The form cites Florida Statute 553.842 and Florida Administrative Code 9B-72.
Is the sheet part of a Walton County building permit submittal?
Yes. It is item 9 on the Walton County Building Department Checklist for Building Permits, which notes that the form must be signed.
Where do I find the product approval numbers?
Walton County’s permit checklist says you may get approval numbers from the vendor or supplier, or from www.floridabuilding.org. The sheet itself recommends contacting your local product supplier if you do not know a product’s approval number.
Which sections are on the Walton County sheet?
A. Exterior Doors, B. Windows, C. Panel Wall, D. Roofing Products, E. Shutters, F. Skylights, G. Structural Components and H. New Exterior Envelope Products.
What if a product did not demonstrate product approval at plan review?
The sheet lists those products on its signature section. The contractor states that at inspection the following must be available to the inspector on the jobsite: a copy of the product approval, the performance characteristics the product was tested and certified to comply with, and a copy of the manufacturer’s installation requirements, and that the products may have to be removed if approval cannot be demonstrated during inspection.
Can I fill out the Walton County sheet online?
Yes. On ProdApproval’s contractor form you choose a manufacturer and product, or type an FL approval number, and the row fills in the product, design pressure, wind borne debris protection and approval number. Searching and filling are free without an account. Print PDF saves a PDF that follows Walton County’s sheet, including the signature page; printing requires signing in.
Is the ProdApproval PDF the county’s own file?
No. ProdApproval rebuilds the sheet with the county’s title, instructions, columns and sections A–H, and adds a section I for impact protective systems. Sign it before you submit it.
How much does printing cost?
The Free plan includes 3 Print / Save-to-PDF fills or exports per calendar month (Central Time). Solo is $19 per month or $190 per year for one user. Firm is $49 per month or $490 per year and includes up to 5 seats. Solo and Firm include unlimited fills and exports.